Laser cutting machine uses different auxiliary gas to cut different data. The pressure of the auxiliary gas and the required flow rate vary with the thickness of the cutting data. Laser cutting gas is mainly used for guiding: laser gas (laser generator is used for laser gas), compressed air (usually used to maintain the optical path, and some manufacturers are also used for maintenance), natural gas (that is, the gas for starting the nozzle) and oxygen cutting carbon steel, the purity of which is generally 99.5% or higher.
Its main function is to support combustion and blow away molten materials. The pressure and flow rate of laser cutting shoe manufacturers are different, which is closely related to the size of cutting nozzle and the thickness of cutting data plate. The pressure is generally 0.3-0.8mpa, and the cutting nozzle is generally 0.02-0.05mpa. It is not easy to say the outlet flow, such as cutting 22mm carbon steel, some manufacturers need to achieve 10m3 / h flow (including double cutting nozzle maintenance oxygen).
Nitrogen is used to cut stainless steel. The effect is to eliminate the oxidation reaction and blow away the melt. The nitrogen purity has higher requirements (especially for stainless steel of 8mm or above, it is generally required to reach 99.999% or above), and the pressure requirements are relatively large. Generally, 1MPa is required, such as cutting stainless steel of 12mm or above, or thicker to 25mm, the pressure requirements are higher, more than 2MPa or higher. According to the type of cutting nozzle, there are some changes, but the changes are very large, for example, some manufacturers cut 12mm stainless steel to 150m3 / h, Cut 3mm, only the flow rate is less than 50m3 / h.
In the laser cutting process, the auxiliary gas must have a satisfactory pressure to completely remove the waste generated by cutting. In general, when cutting thick workpieces, the pressure should be reduced, and the residue on the workpieces will damage the cutting edge. The gas pressure can improve the cutting speed, but when it reaches the maximum, the continuous gas pressure will reduce the cutting speed.
The reason for the high pressure of the lower auxiliary gas and the decrease of the cutting speed can be attributed to the high hanging air speed and the cooling effect influence area which enhance the cooling effect, and it may also be the laser cooling effect of the shock wave area which intermittently disturbs the air flow. The uneven pressure and temperature in the air flow will cause the change of air field density. Such a density gradient causes the refractive index of the field to change, and then the energy of the beam accumulates, regroups or diverges.
This kind of disturbance will affect the melting ability and sometimes change the shape and structure. If the beam deviates too far, the cutting quality will be reduced. If the spots are too large, they will even lead to serious consequences and cannot be effectively reduced. The corresponding three pressurization methods can have different media schemes according to different pressure differences.
空气充电电压输出,基本是保持流动的空气压力用于激光切割在0.6 - 1.5 Mpa在这种情况下,DTE02空气增压系统设备,如原始气压0.8 Mpa,增压压力可达2 Mpa。如果经过减压阀和减压阀来使用压力、喷嘴类型、流量不足的话，可以用DTE02增压泵来增压。
The output of air charging voltage is basically to maintain the flowing air pressure for laser cutting at 0.6 - 1.5 MPa. In this case, Shandong Xinnuo dte02 air pressurization system equipment, such as the original air pressure of 0.8 MPa, pressurization pressure up to 2 MPa. If the pressure, nozzle type and flow are insufficient through the pressure reducing valve and pressure reducing valve, dte02 booster pump can be used for boosting.
所需氧气和氮气的纯度气体不能减少,大家可以使用xinuo DTE02气体增压系统(这增压系统可以加压介质的压力增加到1.6 mpa的压力驱动下0.8 mpa),及其增压缸增压过程的独立操作不会导致纯度降低,二次污染。
The purity gas of oxygen and nitrogen required cannot be reduced. We can use Xinuo dte02 gas pressurization system (this pressurization system can increase the pressure of the pressurized medium to 0.8 MPa driven by 1.6 MPa pressure), and the independent operation of the pressurization process of the pressurization cylinder will not lead to low purity and secondary pollution.
厂家为大家先容的相关内容，想要了解更多内容，欢迎访问网站：The above is the relevant content introduced by the gas booster pump manufacturer. For more information, please visit the website: